Design and performance analysis of tangential-axial flow threshing device for oat harvester

Rongxian Wang, Xiangpeng Zhao, Jiangtao Ji, Xin Jin, Bin Li

Abstract


Aiming at the problems of stalks winding and poor threshing performance in the process of mechanical harvesting of oats, a type of threshing and crushing experimental device was designed. The device was composed of a belt conveyor, a tangential-flow threshing drum, an axial-flow threshing drum, a high-speed camera and a testing device. According to a regression orthogonal test method, using the rotation speed of the axial-flow drum, the horizontal center distance, and the vertical height difference of the two threshing drums as experimental factors; using the mass fraction of long stalks and the threshing rate as experimental indexes, a mathematical regression model of factors and indexes was established, and combined parameters were analyzed for the threshing quality and crushing ability. Experimental results showed that this device had the best crushing performance when the rotation speed of the axial-flow drum was 850 r/min, the horizontal center distance was 820 mm, and the vertical height difference was 10 mm, and this device had optimal threshing performance when the rotation speed of the axial-flow drum was 760 r/min, the horizontal center distance was 820 mm, and the vertical height difference was 20 mm. The parameters were optimized by Design-Expert 11 to obtain an optimization result that the rotation speed of the axial-flow drum was 800 r/min, the horizontal center distance was 820 mm, and the vertical height difference was 10 mm. A verification experiment was carried out by using a high-speed camera, and the two groups of parameters were selected for a comparative experiment. Images of material movement between the two threshing drums were captured by the high-speed camera. Experimental results showed that the optimized parameters were beneficial to improving the threshing performance and anti-winding performance of the oat threshing process. This study provides a technical basis for the research and development of oat combine harvesters.
Keywords: tangential-axial flow threshing device, oat, parameter optimization, threshing performance, crushing performance
DOI: 10.25165/j.ijabe.20211406.6173

Citation: Wang R X, Zhao X P, Ji J T, Jin X, Li B. Design and performance analysis of tangential-axial flow threshing device for oat harvester. Int J Agric & Biol Eng, 2021; 14(6): 61–67.

Keywords


tangential-axial flow threshing device, oat, parameter optimization, threshing performance, crushing performance

Full Text:

PDF

References


Liu W Y, Wang D, Zhou H Y, Zhang X Y, Meng H W. Visualization analysis of research hotspots in the field of plant protection on oats. Modern Agricultural Science and Technology, 2020; 3(4): 1-3, 5. (in Chinese)

Tado C J M, Wacker P, Kutzbach H D, Suministrado D C. Development of stripper harvesters: A review. Journal of Agricultural Engineering Research, 1998; 71(2): 103–112.

Craessaerts G, Saeys W, Missotten, B, Baerdemaeker J D. Identification of the cleaning process on combine harvesters, Part II: A fuzzy model for prediction of the sieve losses. Biosystems Engineering, 2010; 106(2): 97–102.

Liang Z W, Li Y M, Xu L Z, Zhao Z, Tang Z. Optimum design of an array structure for the grain loss sensor to upgrade its resolution for harvesting rice in a combine harvester. Biosystems Engineering, 2017; 157(1): 24–34.

Aenlle M L, Brincker R. Modal scaling in operational modal analysis using a finite element model. International Journal of Mechanical Sciences, 2013; 76(1): 86–101.

Alizadeh M R, Allameh A. Threshing force of paddy as affected by loading manner and grain position on the panicle. Research in Agricultural Engineering, 2011; 57(1): 8–12.

Boac J M, Casada M E, Maghirang R C, Harner J P. Material and interaction properties of selected grains and oil seeds for modeling discrete particles. Transactions of the ASABE, 2010; 53 (4): 1201–1216

Mekonnen G G, Josse D B, Martine B. Effect of a cross - flow opening on the performance of a centrifugal fan in a combine harvester: Computational and experimental study. Biosystems Engineering, 2010; 105(2): 247–256.

Li X P, Meng Y J, Zhang J L, Geng L X, Ji J T. Design and test of cleaning device for roller rubbing cylinder sieve of millet. Transactions of the CSAM, 2018; 49(10): 92–102. (in Chinese)

Kundu M, Krishnan P, Kotnala R K, Sumana G. Recent developments in biosensors to combat agricultural challenges and their future prospects. Trends in Food Science & Technology, 2019; 88: 157–178.

Miu P I, Kutzbach H D. Mathematical model of material kinematics in an axial threshing unit. Computers and Electronics in Agriculture, 2007; 58(2): 93–99.

Zhao Z, Li Y M, Chen J, Xu J J. Grain separation loss monitoring system in combine harvester. Computers and Electronics in Agriculture, 2011; 76(2): 183–185.

Su Y, Liu H, Xu Y, Cui T, Qu Z, Zhang D X. Optimization and experiment of spike-tooth elements of axial flow corn threshing device. Transactions of the CSAM, 2018; 49(S1): 265–272. (in Chinese)

Maertens K, Baerdemaeker J D. Flow rate based prediction of threshing process in combine harvesters. Applied Engineering in Agriculture, 2003; 19(4): 383–388.

Jun H J, Choi I S, Kang T G, Choi S, Choi Y, Choi D K, et al. Study on performance improvement of a head-feeding rice combine for foxtail millet harvesting. Journal of Biosystems Engineering, 2015; 40(1): 10–18.

Xu L Z, Li Y M, Wang C H, Xue Z. A combinational threshing and separating unit of combine harvester with a transverse tangential orthogonal and an axial rotor. Transactions of the CSAM, 2014; 45(2): 105–108. (in Chinese)

Wu T Y, Li Y M, Xu L Z, Huang J. Optimization Design of Transmission System for Tangential Longitudinal Threshing Separation Device. Journal of Agricultural Mechanization Research, 2019; 41(10): 242–248. (in Chinese)

Li Y, Xu L Z, Zhou Y, Li Y M. Effect of extractions feed-quantity on airflow field in multi-ducts cleaning device. Transactions of the CSAE, 2017; 33(12): 48–55. (in Chinese)

Li Y M, Wang J P, Xu, L Z, Tang Z, Xu Z H, Wang K J. Design and Experiment on Adjusting Mechanism of Concave Clearance of Combine Harvester Orthogonal. Transactions of the CSAM, 2018; 49(8): 68–75. (in Chinese)

Li Y M, Chen Y, Xu L Z, Li L. Optimization of structural parameters for threshing and separating device in oblique tangential-longitudinal combine. Transactions of the CSAM, 2016; 47(9): 56–61. (in Chinese)

Gebrehiwot M G, Baerdemaeker J D, Baelmans M. Numerical and experimental study of a cross-flow fan for combine cleaning shoes.

Biosystems Engineering, 2010; 106(4): 448–457.

Liao Q X, Xu Y, Yuan J C, Wan X Y, Jiang Y J. Design and experiment on combined tangential and throwing longitudinal axial flow threshing and separating device of rape combine harvester. Transactions of the CSAM, 2019; 50(7): 140–150. (in Chinese)

Yuko U, Masami M, Eiji I, Mori K, Okayasu T, Mitsuoka M. Turbulent flow characteristics of the cleaning wind in combine harvester. Engineering in Agriculture, Environment and Food, 2012; 5(3): 102–106.

Wang S S, Shi Q X, Geng L X, Luo H G. Development of test-bed of semi-feeding millet threshing mechanism. Journal of Chinese Agricultural Mechanization, 2016; 37(12): 27–30. (in Chinese)

Qian K, Wang R X, Geng L X, Jin X, Wang S S. Research on anti-winding performance of slender ductile stalks of tangential flow drum. Journal of Henan University of Science & Technology (Natural Science), 2019; 40(3): 66–71. (in Chinese)

Qian K. The performance experimental study on high-fineness and toughness crop of tangential-axial flow threshing device. Master dissertation. Luoyang, China: Henan University of Science and Technology, 2019; 66p. (in Chinese)

Chattopadhyay P S, Pandey K P. PM—Power and machinery: Impact cutting behaviour of sorghum stalk using a flail-cutter - a mathematical model and its experimental verification. Journal of Agricultural Engineering Research, 2001; 78(4): 369–376.




Copyright (c) 2021 International Journal of Agricultural and Biological Engineering

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.

2023-2026 Copyright IJABE Editing and Publishing Office